...the world's most energy friendly microcontrollers
on compare match, overflow and underflow through the CMOA, COFOA and CUFOA fields in
TIMERn_CCx_CTRL. TIMERn_CCx_CCV can be accessed directly or through the buffer register
TIMERn_CCx_CCVB, see Figure 19.12 (p. 252) . When writing to the buffer register, the value in
TIMERn_CCx_CCVB will be written to TIMERn_CCx_CCV on the next update event. This functionality
ensures glitch free PWM outputs. The CCVBV flag in TIMERn_STATUS indicates whether the
TIMERn_CCx_CCVB register contains data that have not yet been written to the TIMERn_CCx_CCV
register. Note that when writing 0 to TIMERn_CCx_CCVB the CCV value is updated when the timer
counts from 0 to 1. Thus, the compare match for the next period will not happen until the timer reaches
0 again on the way down.
Figure 19.12. TIMER Output Compare/PWM Buffer Functionality
APB Write (CCB)
Load APB CCV B
Update event
Set
Clear
CCV BV
APB Write (CC)
Load CCB
Load APB
CCV
19.3.2.3 Input Capture
In Input Capture Mode, the counter value (TIMERn_CNT) can be captured in the Compare/Capture
Register (TIMERn_CCx_CCV), see Figure 19.13 (p. 252) . In this mode, TIMERn_CCx_CCV
is read-only. Together with the Compare/Capture Buffer Register (TIMERn_CCx_CCVB) the
TIMERn_CCx_CCV form a double-buffered capture registers allowing two subsequent capture events
to take place before a read-out is required. The CCPOL bits in TIMERn_STATUS indicate the polarity
the edge that triggered the capture in TIMERn_CCx_CCV.
Figure 19.13. TIMER Input Capture
Input
z
y
n
TIMERn_CNT m
TIMERn_CCx_CCV
prev. val
m
TIMERn_CCx_CCVB
prev. val
m
y
Read TIMERn_CCx_CCVB
19.3.2.3.1 Period/Pulse-Width Capture
Period and/or pulse-width capture can be achieved by setting the RISEA field in TIMERn_CTRL to
Clear&Start, and select the wanted input from either external pin or PRS, see Figure 19.14 (p. 253) .
For period capture, the Compare/Capture Channel should then be set to input capture on a rising edge
of the same input signal. To capture a the width of a high pulse, the Compare/Capture Channel should
be set to capture on a falling edge of the input signal. To start the measuring period on either a falling
edge or measure the low pulse-width of a signal, opposite polarities should be chosen.
2011-04-12 - d0001_Rev1.10
252
www.energymicro.com
相关PDF资料
EFM32GG-STK3700 KIT STARTER GIANT GECKO
EFM32LG-DK3650 KIT DEV EFM32 LEOPARD GECKO
EK-K7-KC705-CES-G-J KINTEX-7 FPGA KC705 EVAL KIT
EK-S6-SP601-G KIT EVAL SPARTAN 6 SP601
EK-S6-SP605-G KIT EVAL SPARTAN 6 SP605
EK-V6-ML631-G-J VIRTEX-6 HXT FPGA ML631 EVAL KIT
EK-V7-VC707-CES-G VIRTEX-7 VC707 EVAL KIT
EK-Z7-ZC702-CES-G ZYNQ-7000 EPP ZC702 EVAL KIT
相关代理商/技术参数
EFM32GG230F1024 功能描述:ARM微控制器 - MCU 1024KB FL 128KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
EFM32GG230F1024G-E-QFN64R 功能描述:IC MCU 32BIT 1MB FLASH 64QFN 制造商:silicon labs 系列:Giant Gecko 包装:剪切带(CT) 零件状态:在售 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:48MHz 连接性:I2C,IrDA,智能卡,SPI,UART/USART 外设:欠压检测/复位,DMA,POR,PWM,WDT I/O 数:56 程序存储容量:1MB(1M x 8) 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:128K x 8 电压 - 电源(Vcc/Vdd):1.98 V ~ 3.8 V 数据转换器:A/D 8x12b,D/A 2x12b 振荡器类型:内部 工作温度:-40°C ~ 85°C(TA) 封装/外壳:64-VFQFN 裸露焊盘 供应商器件封装:64-QFN(9x9) 标准包装:1
EFM32GG230F1024-QFN64 制造商:Energy Micro AS 功能描述:GIANT GECKO MCU - Cut TR (SOS) 制造商:Energy Micro 功能描述:GIANT GECKO MCU 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 1MB FLASH 64QFN
EFM32GG230F1024-QFN64T 制造商:Energy Micro AS 功能描述:GIANT GECKO MCU - Trays
EFM32GG230F1024-QFN64-T 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 1MB FLASH 64QFN
EFM32-GG230F1024-SK 制造商:Energy Micro AS 功能描述:GIANT GECKO SAMPLE KIT - Bulk
EFM32GG230F1024-T 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 1MB FLASH 64QFN
EFM32GG230F512 功能描述:ARM微控制器 - MCU 512KB FL 128KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT